Don't forget to check your spam folder if you don't get an activation email after joining!!

Pat Teakle Asw 22 6m**

Let us all watch your new project progress.
Dave Mackintosh
Posts: 44
Joined: 26 Dec 2020, 19:02
Location: Cambridgeshire

Re: Pat Teakle Asw 22 6m

Post by Dave Mackintosh »

Thanks for the suggestions chaps. Here are more progress shots of the tail feathers, rough sanded. will finalise servo installation tomorrow,then glass .
I decided on the servo below,8 kilo pull at 4.8v.Should be fine.
Have a fab weekend gentlemen.
tail1.jpg
tail2.jpg
tailcomplete.jpg
ruddpost.jpg
servo.jpg
User avatar
Peter Balcombe
Posts: 1467
Joined: 18 Mar 2015, 10:13
Location: Clevedon, North Somerset, U.K.

Re: Pat Teakle Asw 22 6m

Post by Peter Balcombe »

Where are you planning to put the servo Dave?
In the fin, or will it fit in the tailplane?
Dave Mackintosh
Posts: 44
Joined: 26 Dec 2020, 19:02
Location: Cambridgeshire

Re: Pat Teakle Asw 22 6m

Post by Dave Mackintosh »

Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
User avatar
Peter Balcombe
Posts: 1467
Joined: 18 Mar 2015, 10:13
Location: Clevedon, North Somerset, U.K.

Re: Pat Teakle Asw 22 6m

Post by Peter Balcombe »

Dave Mackintosh wrote: 13 Mar 2021, 18:18 Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
👍
Dave Mackintosh
Posts: 44
Joined: 26 Dec 2020, 19:02
Location: Cambridgeshire

Re: Pat Teakle Asw 22 6m

Post by Dave Mackintosh »

roo Hawkins wrote: 13 Mar 2021, 08:32 Watching. Good luck with the build.
Thanks Roo.
User avatar
Andrew Ray
Posts: 90
Joined: 19 Mar 2015, 19:15
Location: Staffordshire

Re: Pat Teakle Asw 22 6m

Post by Andrew Ray »

Dave Mackintosh wrote: 13 Mar 2021, 18:18 Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
Ah, yes. I don't think I'd try a standard servo in the fin :D

Nice job, tidy workshop too.
Dave Mackintosh
Posts: 44
Joined: 26 Dec 2020, 19:02
Location: Cambridgeshire

Re: Pat Teakle Asw 22 6m

Post by Dave Mackintosh »

Andrew Ray wrote: 15 Mar 2021, 19:54
Dave Mackintosh wrote: 13 Mar 2021, 18:18 Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
Ah, yes. I don't think I'd try a standard servo in the fin :D

Nice job, tidy workshop too.
Thanks Andrew.
Dave Mackintosh
Posts: 44
Joined: 26 Dec 2020, 19:02
Location: Cambridgeshire

Re: Pat Teakle Asw 22 6m

Post by Dave Mackintosh »

Hi folks.
I cnc cut the inner panels tonight, allowing for skin and carbon cuff thickness. I will cut the mid panels tomorrow and sand and prep the inners.
inner.jpg
User avatar
Cliff Evans
Posts: 722
Joined: 29 Dec 2019, 15:13
Location: Bristol
Contact:

Re: Pat Teakle Asw 22 6m

Post by Cliff Evans »

Looks good Dave.
https://lasercutsailplanes.co.uk
https://patteaklegliders.co.uk
Dave Mackintosh
Posts: 44
Joined: 26 Dec 2020, 19:02
Location: Cambridgeshire

Re: Pat Teakle Asw 22 6m

Post by Dave Mackintosh »

Cliff Evans wrote: 15 Mar 2021, 23:55 Looks good Dave.
Thanks Cliff.
Post Reply