Ikarus Meteor 1/3

Let us all watch your new project progress.
User avatar
Cliff Evans
Posts: 1820
Joined: 13 Mar 2015, 10:32
Location: Bristol
Contact:

Re: Ikarus Meteor 1/3

Post by Cliff Evans » 05 Nov 2019, 19:36

Dopieman1 wrote:
05 Nov 2019, 19:14
I have a question. Maybe the other Meteor builders or Jillis can help. Its about the end rib of the rudder. How can that rib fit into the slots of the leading edge of that rudder?
I would ask the builder here, he has already made that section of the tailplane. https://www.rcgroups.com/forums/showthr ... r-33/page3

Jilles
Posts: 172
Joined: 22 Mar 2015, 10:27
Location: Australia
Contact:

Re: Ikarus Meteor 1/3

Post by Jilles » 06 Nov 2019, 03:32

I am in New Zealand ans cannot access my file. I am sure rib ER8 should have a square hole and round hole in the tail end that I do not see. The square hole should take care of the notches in the spar. The ribs to be split over the square hole so it can be fitted to the spar.

Cheers

Jilles

User avatar
Cliff Evans
Posts: 1820
Joined: 13 Mar 2015, 10:32
Location: Bristol
Contact:

Re: Ikarus Meteor 1/3

Post by Cliff Evans » 06 Nov 2019, 08:53

This is what the rib should look like.
ER8.pdf
(15.66 KiB) Downloaded 57 times

Dopieman1
Posts: 18
Joined: 09 Mar 2018, 09:42
Location: Den Bosch

Re: Ikarus Meteor 1/3

Post by Dopieman1 » 06 Nov 2019, 22:40

Thanks Jillis and Cliff for your quick reply and support. The rib is not like in the pdf as it is missing the square hole. But no big deal. I did a small modification and cut the rib in two pieces and added a slot. Hope the picture clarifies!
AF0CCC91-F8C4-4785-A27E-6E20F3174CC1.jpeg
DC34B29A-FFA4-4010-BB2F-DDF59E74B37B.jpeg
78122A09-13BB-4944-8F31-D83A7CCD4B00.jpeg

Dopieman1
Posts: 18
Joined: 09 Mar 2018, 09:42
Location: Den Bosch

Re: Ikarus Meteor 1/3

Post by Dopieman1 » 16 Nov 2019, 08:05

I have received a Fema retract for the Meteor.
Really a nice piece of gear! I will mount it kind of reverse such that the wheel swings up in forward direction just like the real one. Suppose this will not impact on the retraction. There is anyway plenty room for it.
Attachments
075659EE-84FC-4BB9-8C5E-380E1D532A9C.jpeg

Dopieman1
Posts: 18
Joined: 09 Mar 2018, 09:42
Location: Den Bosch

Re: Ikarus Meteor 1/3

Post by Dopieman1 » 20 Nov 2019, 22:37

Today I prepared the rudders for the covering with 0,4 mm ply. First some balsa filling is to be applied to leading and trailing edge. A bit of a time consuming job.
I decided to apply a tube and wire hinge for the rudder. This to allow for the option to disassemble the rudders when needed.
Attachments
26DACB81-BF56-41E3-8F49-FF1BA0D07157.jpeg
7B925B38-0809-4169-8DDD-CCC359578AC8.jpeg

BrianF
Posts: 6
Joined: 19 Mar 2018, 09:36
Location: Brisbane AU

Re: Ikarus Meteor 1/3

Post by BrianF » 21 Nov 2019, 20:15

Hi, I'm building the one on the other forum, very happy to answer Meteor queries here. There are a few things that will make you stop and scratch your head, but there will be one or more solutions out there to get you going again. Apart from the sheeting on one wing the structure on my build is complete.

Dopieman1
Posts: 18
Joined: 09 Mar 2018, 09:42
Location: Den Bosch

Re: Ikarus Meteor 1/3

Post by Dopieman1 » 23 Nov 2019, 07:59

BrianF wrote:
21 Nov 2019, 20:15
Hi, I'm building the one on the other forum, very happy to answer Meteor queries here. There are a few things that will make you stop and scratch your head, but there will be one or more solutions out there to get you going again. Apart from the sheeting on one wing the structure on my build is complete.
Hi Brian,
I am following you on the rcgroups forum and read all your good advices with great interest. This has a big value for the building of the Meteor! See my post #182, that is me!

Dopieman1
Posts: 18
Joined: 09 Mar 2018, 09:42
Location: Den Bosch

Re: Ikarus Meteor 1/3

Post by Dopieman1 » 01 Dec 2019, 18:20

Now covering the rudders with 0,4 mm ply. Thats working fine when pressing with some blocks But this method will for sure not work anymore when dealing with bigger curvatures like around the fin post. So I have tried the ironing method. And indeed, it works perfect! After cooling down the pieces are fixed!
Attachments
IMG_3592.JPG
IMG_3593.JPG

Dopieman1
Posts: 18
Joined: 09 Mar 2018, 09:42
Location: Den Bosch

Re: Ikarus Meteor 1/3

Post by Dopieman1 » 02 Dec 2019, 19:19

I had a small issue with the rudder. I wrongly assumed that I could glue the ply surfaces while putting the rudder on its side on a flat building board. Luckily I inspected the rudder after around 30 minutes when the gue was not fully cured. It was clearly visible that I had a twist in the rudder! So tried to over correct it into right shape. This happened to be quite succesfull. I am happy with the endresult.
Attachments
43FCCE02-136F-40FF-9075-D41237D7B63F.jpeg
B392FEF8-2F28-4B04-ADA3-6054D21B297F.jpeg

Post Reply