H101 Salto 1/5 th scale

Let us all watch your new project progress.
andynrose315
Posts: 14
Joined: 14 Nov 2018, 17:15
Location: nr salisbury

Re: H101 Salto 1/5 th scale

Post by andynrose315 » 27 Feb 2019, 21:10

well all the parts have been drawn. To finalise just thinking what i should use to skin the wings; i have balsa sheeted before but see many use ply. Looking at either 0.8 mm or 0.6 mm ply. Quite a big cost difference so want to make sure i make the right choice. I have made a trial wing panel and tested sheeted it with a spare piece of 0.8 mm ply and quite impressed with the finish. I was going to go with the 0.8 mm - is this a reasonable choice for a 3 m span?

User avatar
chris williams
Posts: 877
Joined: 10 Mar 2015, 10:50
Location: Blandford Dorset

Re: H101 Salto 1/5 th scale

Post by chris williams » 27 Feb 2019, 22:05

Oooh, bad choice IMHO... Hard 1.5mm balsa works not only for small models but large models too....

User avatar
RobbieB
Posts: 464
Joined: 07 Mar 2015, 22:22
Location: North West
Contact:

Re: H101 Salto 1/5 th scale

Post by RobbieB » 27 Feb 2019, 22:15

Absolutely - too heavy and unnecessary for a 3m model; 1.5mm balsa will be fine but if you prefer to go down the ply road then 0.4mm at most.

andynrose315
Posts: 14
Joined: 14 Nov 2018, 17:15
Location: nr salisbury

Re: H101 Salto 1/5 th scale

Post by andynrose315 » 27 Feb 2019, 22:23

thank you - balsa it is!

andynrose315
Posts: 14
Joined: 14 Nov 2018, 17:15
Location: nr salisbury

Re: H101 Salto 1/5 th scale

Post by andynrose315 » 20 May 2019, 13:13

Well parts received in the post. No excuses to start.
Attachments
45B58665-5FAE-478A-ADEA-25FAC27BEAC3.jpeg
E0720AE3-AAC7-4F13-A8FB-5F3D36A623D5.jpeg
E231DA84-3BF9-48CD-9A51-04698173930D.jpeg

andynrose315
Posts: 14
Joined: 14 Nov 2018, 17:15
Location: nr salisbury

Re: H101 Salto 1/5 th scale

Post by andynrose315 » 26 May 2019, 23:32

Made a start. A few ribs in place and soon one side planked. A few modifications to the cad file needed and think I will try slightly narrower planks when I turn it over.
Attachments
9552CC0C-8A4B-4175-B10E-9751A326CA0B.jpeg
First pieces on the board.
FB250977-973E-4153-89F5-C5431EEF7C0F.jpeg
Starting with centre ribs. Using carbon tubes to align wing joiner.
25653DE3-8237-4DD4-B696-9AD48E848177.jpeg
Planking nearly completed on one side.

andynrose315
Posts: 14
Joined: 14 Nov 2018, 17:15
Location: nr salisbury

Re: H101 Salto 1/5 th scale

Post by andynrose315 » 03 Jun 2019, 20:00

Progress on planking fuselage. Changed the width of the planks for the last two thirds which made things easier. Still learn by your mistakes and picked up a few additions to the parts I drew.
Attachments
A8E4BAD5-7B2C-4CAF-BC50-E8D7FBF1F96C.jpeg
4CEB8942-7642-45B8-9BF3-3990CD125A24.jpeg

andynrose315
Posts: 14
Joined: 14 Nov 2018, 17:15
Location: nr salisbury

Re: H101 Salto 1/5 th scale

Post by andynrose315 » 13 Jun 2019, 19:02

Bit more progress. Wings I’m building in two panels as limited by building board. One inner panel is skinned on both side the other one side. Had a few issues trying to get the balsa in full contact with the ribs at the trailing edge where the airfoil curves up. Trial fitted one to the fuselage and seems a good fit.
Attachments
7A25E65F-5016-4918-AE90-93B985952503.jpeg
6D423D1D-0C15-4839-9304-DCCB6E31E6EE.jpeg
C0579BC9-7D29-4911-AB84-E60E68BD611F.jpeg

Post Reply