-
- Administrator
-
-
Before your membership becomes valid, you will receive an email that must be answered.
Please check your spam folder or this email.
Pat Teakle Asw 22 6m**
-
- Posts: 45
- Joined: 26 Dec 2020, 19:02
- Location: Cambridgeshire
Re: Pat Teakle Asw 22 6m
Thanks for the suggestions chaps. Here are more progress shots of the tail feathers, rough sanded. will finalise servo installation tomorrow,then glass .
I decided on the servo below,8 kilo pull at 4.8v.Should be fine.
Have a fab weekend gentlemen.
I decided on the servo below,8 kilo pull at 4.8v.Should be fine.
Have a fab weekend gentlemen.
- Peter Balcombe
- Posts: 1399
- Joined: 18 Mar 2015, 10:13
- Location: Clevedon, North Somerset, U.K.
Re: Pat Teakle Asw 22 6m
Where are you planning to put the servo Dave?
In the fin, or will it fit in the tailplane?
In the fin, or will it fit in the tailplane?
-
- Posts: 45
- Joined: 26 Dec 2020, 19:02
- Location: Cambridgeshire
Re: Pat Teakle Asw 22 6m
Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
- Peter Balcombe
- Posts: 1399
- Joined: 18 Mar 2015, 10:13
- Location: Clevedon, North Somerset, U.K.
Re: Pat Teakle Asw 22 6m
Dave Mackintosh wrote: ↑13 Mar 2021, 18:18 Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
-
- Posts: 45
- Joined: 26 Dec 2020, 19:02
- Location: Cambridgeshire
Re: Pat Teakle Asw 22 6m
Thanks Roo.
- Andrew Ray
- Posts: 88
- Joined: 19 Mar 2015, 19:15
- Location: Staffordshire
Re: Pat Teakle Asw 22 6m
Ah, yes. I don't think I'd try a standard servo in the finDave Mackintosh wrote: ↑13 Mar 2021, 18:18 Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
Nice job, tidy workshop too.
-
- Posts: 45
- Joined: 26 Dec 2020, 19:02
- Location: Cambridgeshire
Re: Pat Teakle Asw 22 6m
Thanks Andrew.Andrew Ray wrote: ↑15 Mar 2021, 19:54Ah, yes. I don't think I'd try a standard servo in the finDave Mackintosh wrote: ↑13 Mar 2021, 18:18 Hi Peter, In the fin with an 80mm x m3 pushrod and metal clevis. Threaded both ends with lock nuts.
Nice job, tidy workshop too.
-
- Posts: 45
- Joined: 26 Dec 2020, 19:02
- Location: Cambridgeshire
Re: Pat Teakle Asw 22 6m
Hi folks.
I cnc cut the inner panels tonight, allowing for skin and carbon cuff thickness. I will cut the mid panels tomorrow and sand and prep the inners.
I cnc cut the inner panels tonight, allowing for skin and carbon cuff thickness. I will cut the mid panels tomorrow and sand and prep the inners.
- Cliff Evans
- Posts: 1035
- Joined: 29 Dec 2019, 15:13
- Location: Bristol
- Contact:
Re: Pat Teakle Asw 22 6m
Looks good Dave.
https://lasercutsailplanes.co.uk
https://patteaklegliders.co.uk
https://patteaklegliders.co.uk
-
- Posts: 45
- Joined: 26 Dec 2020, 19:02
- Location: Cambridgeshire
Re: Pat Teakle Asw 22 6m
Thanks Cliff.